Amsoil Product Line
 
Technilube.com Logo
Buy Now
    Home     |     Media     |     I'm Ready to Buy     |     Buy at Cost and/or Request Info     |     Where I'll Be     |     Contact    









 
AltruHealth.com

 

 

 

 

 

 



Back to Articles Featuring Amsoil

Power Stroke Registry - Summer 2003

 

The True Measure of Lubricant Quality

by Ed Newman

This article appeared in the Power Stroke Registry
Summer 2003

Making and recording measurements has been one of the hallmarks of the Age of Enlightenment. It seems like modern people measure everything. We have measures of time, such as weeks, hours, minutes, and years. We have measures of mass, such as grams, pounds and tons. We have measures of sound volume, of energy, of radioactivity, of pressure, of type font sizes, of land mass, and of speed.

AUTOMOTIVE RELATED MEASUREMENTS

Horsepower, as you might guess, is the amount of power exerted by one horse pulling. After many careful measurements James Watt, inventor of the steam engine, determined that a horse can lift 550 pounds at a rate of one foot per second, which translates into 745.7 watts. Some clever American engineers decided that manpower should have a measurement as well, equivalent to 0.1 horsepower or 74.57 watts.

MPG is the familiar acronym for miles per gallon, which measures the rate of fuel consumption in a motor vehicle. One mile per gallon equals approximately 0.4252 kilometers per liter. MPH is our common measure of speed. One mile per hour equals 22/15ths feet per second or 1.609 kilometers per hour or 0.447 meters per second.

RPM means revolutions per minute, a unit of frequency as a measure of rotation rates in mechanics. In cars RPM is measured by a tachometer. Some motorists pay attention to RPM so they don't overrev and cause component failure. Race car drivers try to keep RPM rates in a range that will provide maximum power.

OIL MEASURES

A quart as a unit of volume is so named because it represents one quarter of a gallon. When measuring liquid, one quart is 32 fluid ounces, or 57.75 cubic inches. On the other hand, when measuring dry goods like pecans or blueberries, a quart is 67.201 cubic inches. Go figure.

Drums are sometimes used for measuring oil, containing 55 U.S. gallons or about 208.198 liters. Drums are not the same as barrels, the standard unit of volume for measuring crude. One drum is equivalent to 1.3095 barrels. A barrel is equivalent to 42 U.S. gallons, which is coincidentally the same size as a traditional wine barrel, more commonly called a tierce.

But what about oil quality? What are the criteria that are important when measuring the performance quality of a motor oil?

Part of the answer comes from understanding the role that motor oils play when it comes to engine lubrication. Another part of the answer comes from understanding that we live in a scientific age in which nearly everything can be, and often has been, measured. Knowing what to measure and how to measure it is an important part of good decision making. We're talking motor oil here.

THE ROLE OF MOTOR OIL

Before we can discuss what makes a good motor oil, it helps to understand what role motor oil actually plays in the performance of an engine.

While motor oils serve a variety of functions, they are primarily necessary to lubricate and to cool the engine. When the engine is at rest, the motor oil sits in the bottom of the engine block in what is called the oil pan. Upon start-up, an oil pump feeds oil from the pan to the oil distribution system by means of a network of passages, tubes, grooves and holes leading to the engine bearings and other surfaces needing pressurized oil for lubrication. Other parts, like the overhead valve system, receive a carefully controlled quantity of non-pressurized oil through splashing or spray.

In addition to lubricating and cooling engine parts, motor oil must allow easy starting, protect the engine from corrosion and oxidation, keep the engine clean, form a tight seal between piston rings and cylinder walls and help the engine use fuel efficiently.

In days gone by motor oil was made from the throwaway byproducts of a barrel of crude oil after everything useful was taken from it. In those early days the filter, if you had one at all, was a by-pass type, filtering only a small percentage of the oil. In some instance the filter was little more than a screen and the oil was changed every five hundred or thousand miles. (Some of us recall grandpa's stories of tires needing to be changed on every trip to town, the idea of longevity being somewhat foreign back then.)

As cars and their engines became more sophisticated, so too the requirements of a lubricant became increasingly demanding. In the 1960's jet fighter pilots and their mechanics were becoming aware of the advantages of synthetic oils, and a few of them experimented with the notion of synthetic lubrication for automobiles. One of these pilots, Lt. Colonel Albert J. Amatuzio, went further than the haphazard experiments of his peers. His ten year quest resulted in the development of AMSOIL, the first automotive synthetic motor oil to exceed the certification requirements of the American Petroleum Institute (API).

SYNTHETIC VS. CONVENTIONAL PETROLEUM

Conventional lubricants are refined from crude oil which has thousands of types of molecules. Refining is a process of physically separating the impurities from the oil and further separating the light and heavy components. Because refining separates products by weight, it groups molecules of similar weight and dissimilar structure. The result is a lubricant with a wide assortment of molecules. Some of the substances in crude oil are detrimental to lubrication. Paraffins, for example, are a common conventional oil contaminant that causes motor oil to thicken in cold temperatures.

Synthetic motor oils are made from pure chemicals, not refined crude. Their components are chemically reacted to produce finished products with pre-designed performance characteristics. Because of their molecular uniformity, they excel in reducing friction, which improves fuel efficiency, controls heat and reduces wear. This molecular uniformity also helps synthetics resist thinning in hot temperatures and thickening in cold.

MEASURES THAT MATTER

The American Society for Testing and Materials recognized the need for uniform procedures that can be duplicated and verified by laboratories in any location. The goal of establishing standards is so important that the official publication of ASTM International is called Standardization News.

Founded in 1898 and completely voluntary, ASTM is now one of the largest non-profit standards development systems in the world. The organization currently has 134 committees that write standardized test methods for materials, products, systems and services. More than 8500 ASTM specifications have been established for products as diverse as metal, paints, plastics, textiles, energy, consumer products, medical services and instruments and even the environment.

Developing standard measurement methods is part of the task of ASTM. Equally important is determining what measures are important, tests that actually correspond to what the function of motor oil is intended to fulfill. What follows here are some tests commonly used to evaluate motor oil performance.

ASTM D-445 Kinematic Viscosity

The proper operation of equipment depends on the proper kinematic viscosity of the oil at operating temperatures. Kinematic viscosity is a measure of a liquid's flow under the influence of gravity. Some companies formulate their lubes to tighter specs than others. One recent study revealed that one in five off-the-shelf motor oils tested were outside the acceptable performance range for their stated viscosities.

ASTM D-2270 Viscosity Index

This test indicates how much a lube's viscosity will change according to changes in temperature from 40 degrees C and 100 degrees C. The higher the viscosity index the better for motor oils that must perform in locations with temperature variations.

ASTM D-5293 Cold Crank Simulator Apparent Viscosity

Cold crank viscosity affects the startability of engines in cold temperatures. Low cold cranking viscosities make for easier cold cranking and more dependable cold temperature starting, and less drain on batteries.

ASTM D-3829 Borderline Pumping Temperature

This test is used to predict the lowest temperature at which a motor oil can be continuously and adequately supplied to an enginešs components. As the name suggests, the lower the temperature, the better the oil circulates in cold weather. Synthetic oils are famed for the extreme low temperature protection.

ASTM D-97 Pour Point

This test identifies the lowest temperature at which oil flows.

ASTM D-92 Flash Point and Fire Point

Flash point indicates the temperature at which a specimen vapors will ignite. Flash point assesses the overall hazard of a material and is used in shipping and safety regulations to define "flammable" and "combustible" materials. Fire point measures the temperature at which a specimen will remain burning for five seconds. Synthetic lubricants with high flash and fire points are safer to use and transport than petroleum lubes with lower ones. High flash point is indicative of a greater high temperature operating range and better quality base stock.

ASTM D-4683 High Temp, High Shear Viscosity

This test is representative of the conditions encountered in the bearings of automotive engines in severe service. Lubricants with high scores, such as premium synthetics, maintain their viscosity in high temperatures after exposure to high shear. This means that they continue to protect bearings even after exposure to severe service conditions.

ASTM D-892 Foaming Tendency

This test is important because of the turbulent environment in which motor oils are required to perform. Foaming can lead to inadequate lubrication, cavitation and mechanical failure.

ASTM D-4172B Four Ball Wear Test

The Four Ball Wear Test determines the relative wear prevention properties of lubricants in sliding contact. The test involves three fixed balls in a bath of lubricant with a fourth ball in rolling contact under pressure at a specific level of severity. Wear protection is gauged by measuring the wear scar that develops. A smaller wear scar means better protection in typical engine operations.

ASTM D-5800 Noack Volatility

Oil volatility is the measure of how susceptible oil is to boil-off under high heat conditions. Petroleum oils experience significant boil-off during high temperature engine operation and subsequently higher oil consumption. Evaporation loss contributes to damaging deposits, sticky piston rings and oil blow-by, resulting in a drag on performance and reduced engine life. Synthetic oils are far more impervious to this kind of degradation. The lower volatility of synthetics is another reason they are also better for the environment than conventional products.

SAE J1321 Joint TMC/SAE Fuel Consumption Test Procedure - Type II

The Society of Automotive Engineers has devised a test to measure fuel consumption and fuel economy. In a demonstration involving over-the-road trucks an improvement of 8.2% was achieved by switching from conventional lubes to synthetic lubricants (in this case AMSOIL products) in the drivetrain and engine.

Here's an interesting, undisputed fact. By every one of these measures premium synthetic motor oils are superior to conventional petroleum motor oils. This truth is never even questioned by industry professionals.

So why, one might ask, isn't everyone using synthetic motor oils and lubes? Here's one possible reason. To divert attention away from the performance measures above the major oil companies focus on one other measure: price.

PRICE

Ironically, we live in an era in which people are spending more money than ever on large vehicles or cool looking vehicles -- PT Cruisers, SUVs, Hummers, and dualies. Insurance payments alone in most households run ten times greater than motor oil costs. People are passionate about their vehicles. How can they not be equally dedicated to protecting their investment by using premium lubricants that promise longer life to the object of their passion. You wouldn't expect price to be that big of a deal, yet it is for some people. For this reason the price myth must be addressed.

When people talk about price, they generally think in terms of initial cost instead of life cycle cost. Price is only an issue if you apply the 3,000 mile oil change rule to all motor oils alike. In truth, the service life of synthetics can be extended much longer due to their resistance to oxidation and other forms of degradation. With proper filtration engine oil can be safely used for much longer periods, and is thereby less costly than petroleum in the long run. Add to this the reduced fuel consumption, fewer maintenance bills and optimal performance characteristics and running anything but a premium synthetic motor oil should not even be a consideration.

CLOSING THOUGHTS

As you can readily see there is no single measure that stands alone as the signature of superior performance. A motor oil serves a variety of functions in a range of roles inside the engine. What tests do show is that synthetic motor oils as a class are far and away superior to petroleum based products.

 

Back to Articles Featuring Amsoil
Home Wholesale Sitemap Brochures Amsoil